Welding, Fabrication and Painting
+ Post New Thread
Page 40 of 65 FirstFirst ... 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 ... LastLast
Threads 976 to 1000 of 1603

Forum: Welding, Fabrication and Painting

Hardcore DIY covering aspects of welding, fabrication, body repair/prep, painting etc.

  1. Home Spray Setup

    Started by richie00boy‎, 10-06-2009 15:23
    • Replies: 4
    • Views: 498
    11-06-2009 12:14 Go to last post
  2. painting help

    Started by wilde-one‎, 26-05-2009 08:57
    • Replies: 2
    • Views: 327
    10-06-2009 18:14 Go to last post
  3. cutting flanges??

    Started by Gary_808‎, 08-06-2009 13:58
    • Replies: 10
    • Views: 469
    10-06-2009 17:53 Go to last post
  4. spray painting advice needed

    Started by stt‎, 25-04-2009 03:14
    • Replies: 5
    • Views: 554
    10-06-2009 15:31 Go to last post
  5. Laquer & primer info

    Started by sneakycorsa‎, 07-02-2009 00:01
    • Replies: 6
    • Views: 457
    10-06-2009 15:14 Go to last post
  6. Question Surface Rust

    Started by RhysWilliams3‎, 05-06-2009 10:02
    • Replies: 4
    • Views: 477
    08-06-2009 09:02 Go to last post
  7. 3"downpipe

    Started by rubymir05‎, 05-06-2009 17:28
    • Replies: 6
    • Views: 404
    05-06-2009 19:51 Go to last post
  8. Exclamation what colour??

    Started by Balley77vauX‎, 04-06-2009 16:20
    • Replies: 5
    • Views: 292
    04-06-2009 20:05 Go to last post
  9. help with nova plateing kit locations

    Started by siby‎, 03-06-2009 21:38
    • Replies: 3
    • Views: 368
    04-06-2009 11:51 Go to last post
  10. help needed on welding cast

    Started by astra mk3 8vt‎, 26-12-2008 15:22
    • Replies: 15
    • Views: 2,345
    01-06-2009 10:42 Go to last post
  11. Preserving a sandblasted body

    Started by Novasportowner‎, 28-05-2009 22:23
    • Replies: 4
    • Views: 528
    31-05-2009 16:42 Go to last post
  12. does vinegar also attack clean metal?

    Started by joe joe‎, 30-05-2009 14:26
    • Replies: 3
    • Views: 798
    31-05-2009 00:10 Go to last post
  13. corsa b rear latch pin panel

    Started by Richardhhhha‎, 25-05-2009 23:18
    • Replies: 2
    • Views: 378
    26-05-2009 12:37 Go to last post
  14. Hmm Will G3 make this shine????

    Started by Todi-Corsa‎, 25-05-2009 20:42
    • Replies: 14
    • Views: 961
    25-05-2009 22:45 Go to last post
  15. Spraying? Would like some primer info?

    Started by desso64‎, 29-04-2009 22:56
    • Replies: 22
    • Views: 823
    25-05-2009 22:24 Go to last post
  16. machining hubs

    Started by corsagsi16vplym‎, 27-04-2008 19:18
    • Replies: 22
    • Views: 1,136
    15-05-2009 17:09 Go to last post
  17. Bare weld prepping?

    Started by Rick Draper‎, 23-04-2009 18:05
    • Replies: 3
    • Views: 579
    23-04-2009 21:11 Go to last post
  18. Spraying Alloys...

    Started by Tiga‎, 07-04-2009 14:02
    • Replies: 3
    • Views: 558
    07-04-2009 18:52 Go to last post
    • Replies: 5
    • Views: 7,449
    29-03-2009 12:26 Go to last post
  19. whats the best primer to use

    Started by B14ckburn‎, 28-02-2009 14:27
    • Replies: 7
    • Views: 839
    03-03-2009 20:51 Go to last post
  20. Whats the best primer to use?

    Started by B14ckburn‎, 27-02-2009 01:54
    • Replies: 6
    • Views: 489
    02-03-2009 18:11 Go to last post
    • Replies: 0
    • Views: 260
    23-02-2009 20:57 Go to last post
  21. Painting rubber...

    Started by Lugy‎, 18-02-2009 19:02
    • Replies: 8
    • Views: 350
    19-02-2009 21:32 Go to last post
  22. Welding a S/S t3/4 flange into a cut let manifold

    Started by Knoxygtt‎, 19-02-2009 01:17
    • Replies: 3
    • Views: 389
    19-02-2009 13:28 Go to last post
  23. Undersealing and Spraying Q's

    Started by Dale‎, 02-02-2009 23:27
    • Replies: 0
    • Views: 371
    02-02-2009 23:27 Go to last post

+ Post New Thread
Page 40 of 65 FirstFirst ... 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 200 replies or 1000 views
Hot thread with unread posts
More than 200 replies or 1000 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts