Pedal Test - Fault Code Reading Instructions
+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 25 of 36

Thread: Pedal Test - Fault Code Reading Instructions

  1. #1
    Administrator. GTE 16v's Avatar
    Join Date
    Jul 2004
    Posts
    11,148
    Drives
    3 x Astras.

    Thumbs up Pedal Test - Fault Code Reading Instructions

    Tools
    No specialist tools are needed, only 2 working feet are required, 30 seconds of your time and pen & paper to write down the codes

    STEP 1:
    Get inside your vehicle a firmly place yourself in your seat. Once in, press both the accelerate and brake pedal together

    STEP 2:
    With both pedals pressed, put your key in the ignition and turn it to position 2, which is the position that switches all auxilary heating on but not the engine

    STEP 3:Once done, the spanner light will start flashing

    if it flashes 10 times it means the number is '0' and any other flashes corresponds to a number with a pause between each number

    for example code P0110
    the light will flash ten times then pause (2sec Or 1 not sure) flash once, (2sec pause) flash once, (2 sec pause) then flash ten times


    if you have more than one code it will stop for a break between each code


    however if you don’t have any code stored it will start Flashing and keeps on flashing until you release the pedals

    If you follow the above steps you are certain to find codes without ever having to plug an OBD equipment

    Code list is here

    P0030 O2 Sensor Heater Circuit Range/Performance (Bank 1 Sensor 1) C-29
    P0036 O2 Sensor Heater Circuit Range/Performance (Bank 1 Sensor 2) C-31
    P0100 Mass or volume air flow circuit high input C-10
    P0100 Mass or volume air flow circuit low input C-10
    P0110 Intake Air Temperature Circuit High Input C-12
    P0110 Intake Air Temperature Circuit Low Input C-12
    P0115 Engine Coolant Temperature Circuit High Input C-11
    P0115 Engine Coolant Temperature Circuit Low Input C-11
    P0115 Engine coolant temperature circuit malfunction C-11
    P0120 Throttle Position Sensor (TPS) Circuit 1 Voltage High C-09
    P0120 Throttle Position Sensor (TPS) Circuit 1 Voltage Low C-09
    P0120 Throttle Position Sensor 1-2 Correlation C-09
    P0130 O2 Sensor Circuit High Voltage (Bank 1 Sensor 1) C-30
    P0130 O2 Sensor 1 Circuit Voltage Low C-30
    P0130 O2 Sensor 1 Open Circuit C-30
    P0130 O2 Sensor 1 Incorrect Signal C-30
    P0134 O2 Sensor Circuit Open (Bank 1 Sensor 1) C-30
    P0135 O2 Sensor Heater Circuit High Voltage (Bank 1 Sensor 1) C-29
    P0135 O2 Sensor Heater Circuit Low Voltage (Bank 1 Sensor 1) C-29
    P0135 O2 Sensor Heater Circuit Open (Bank 1 Sensor 1) C-29
    P0136 O2 Sensor Circuit High Voltage (Bank 1 Sensor 2) C-32
    P0136 O2 Sensor 2 Circuit Voltage Low C-32
    P0136 O2 Sensor 2 Open Circuit C-32
    P0139 O2 Sensor 1 Incorrect Signal C-30
    P0140 O2 Sensor 2 Incorrect Signal C-32
    P0141 O2 Sensor Heater Circuit High Voltage (Bank 1 Sensor 2) C-31
    P0141 O2 Sensor Heater Circuit Low Voltage (Bank 1 Sensor 2) C-31
    P0141 O2 Sensor Heater Circuit Open (Bank 1 Sensor 2) C-31
    P0170 Rich Exhaust C-30
    P0170 Lean Exhaust C-30
    P0201 Cylinder 1 injector circuit high C-23
    P0201 Cylinder 1 injector circuit low C-23
    P0201 Cylinder 1 Injector Circuit Open C-23
    P0202 Cylinder 2 injector circuit high C-24
    P0202 Cylinder 2 injector circuit low C-24
    P0202 Cylinder 2 Injector Circuit Open C-24
    P0203 Cylinder 3 injector circuit high C-25
    P0203 Cylinder 3 injector circuit low C-25
    P0203 Cylinder 3 Injector Circuit Open C-25
    P0204 Cylinder 4 injector circuit high C-26
    P0204 Cylinder 4 injector circuit low C-26
    P0204 Cylinder 4 Injector Circuit Open C-26
    P0219 Engine overspeed condition C-43
    P0220 Throttle Position Sensor (TPS) Circuit 2 Voltage High C-09
    P0220 Throttle Position Sensor (TPS) Circuit 2 Voltage Low C-09
    P0220 Throttle Position Sensor 1-2 Correlation C-09
    P0230 Fuel pump secondary circuit high C-07
    P0230 Fuel Pump Relay Open Circuit C-07
    P0300 Misfire Unidentified Cylinder Detected B-21
    P0301 Cylinder 1 Misfire Detected B-22
    P0301 Cylinder 1 Misfire Detected B-22
    P0301 Cylinder 1 Misfire Detected B-22
    P0302 Cylinder 2 Misfire Detected B-22
    P0302 Cylinder 2 Misfire Detected B-22
    P0302 Cylinder 2 Misfire Detected B-22
    P0303 Cylinder 3 Misfire Detected B-22
    P0303 Cylinder 3 Misfire Detected B-22
    P0303 Cylinder 3 Misfire Detected B-22
    P0304 Cylinder 4 Misfire Detected B-22
    P0304 Cylinder 4 Misfire Detected B-22
    P0304 Cylinder 4 Misfire Detected B-22
    P0325 Knock Sensor 1 Circuit no Signal C-27
    P0335 Crankshaft Sensor Incorrect Signal C-06
    P0335 Crankshaft Sensor Open Circuit C-06
    P0335 Crankshaft Sensor Incorrect Signal C-06
    P0340 Camshaft Position Sensor Circuit No Signal C-13
    P0340 Camshaft Sensor Incorrect Signal C-13
    P0351 Ignition Coil 1 High Input B-23
    P0351 Ignition Coil 1 Incorrect Signal B-23
    P0352 Ignition Coil 2 High Input B-23
    P0352 Ignition Coil 2 Incorrect Signal B-23
    P0353 Ignition Coil 3 High Input B-23
    P0353 Ignition Coil 3 Incorrect Signal B-23
    P0354 Ignition Coil 4 High Input B-23
    P0354 Ignition Coil 4 Incorrect Signal B-23
    P0420 Catalyst Efficiency Above Threshold C-31
    P0443 Evaporative emission control system purge control valve circuit shorted C-28
    P0443 Evaporative emission control system purge control valve circuit shorted C-28
    P0443 Evaporative emission control system purge control valve circuit open C-28
    P0460 Fuel Level Sensor Circuit High Input C-14
    P0460 Fuel Level Sensor Circuit Low Input C-14
    P0460 Purge flow sensor circuit malfunction C-14
    P0500 Vehicle speed sensor malfunction B-10
    P0530 A/C Refrigerant Pressure Sensor Circuit High Input Air Conditioning System B-05
    P0530 A/C Refrigerant Pressure Sensor Circuit Open Air Conditioning System B-05
    P0560 System Voltage High Input C-04
    P0560 System Voltage Low Input C-04
    P0565 Cruise Control SET and RESUME active C-17
    P0566 Cruise Control Off Signal Circuit no or Incorrect Signal C-17
    P0567 Cruise Control Resume Signal High Input C-17
    P0568 Cruise Control Set Signal Circuit High Input C-17
    P0571 Brake Switch Circuit Low Input C-15
    P0602 Powertrain Control Module Not Programmed C-02
    P0602 Security Code Not Programmed C-02
    P0602 Vehicle Identification Number Not Programmed C-02
    P0602 Variant-Coding Not Programmed C-02
    P0606 Control Unit Re-Initialisation C-02
    P0650 Malfunction Indicator (MI) Control Circuit High C-36
    P0650 Malfunction Indicator (MI) Control Circuit Open C-36
    P0700 EOBD Error stored by Transmission Control (TC) Modul B-06
    P0700 MIL request from Transmission Control (TC) Modul B-06
    P0704 Clutch Switch Input Circuit High Input C-16
    P1110 Variable Intake Manifold Signal High C-33
    P1110 Variable Intake Manifold Signal Low C-33
    P1110 Variable Intake Manifold Open Circuit C-33
    P1120 Accelerator Pedal Position Sensor 1 High Input C-08
    P1120 Accelerator Pedal Position Sensor 1 Low Input C-08
    P1120 Accelerator Pedal Position Sensor 1-2 Correlation C-08
    P1122 Accelerator Pedal Position Sensor 2 High Input C-08
    P1122 Accelerator Pedal Position Sensor 2 Low Input C-08
    P1130 O2 Sensor 1 Signal Out of Range C-30
    P1130 O2 Sensor 1 Signal no Activity detected C-30
    P1130 O2 Sensor 1 Signal Switching Time Error C-30
    P1170 System too rich (Bank 1) C-30
    P1170 System too lean (Bank 1) C-30
    P1230 Main Relay Circuit Voltage High C-03
    P1230 Main Relay Open Circuit C-03
    P1326 Knock Control Maximum Spark Limit Cylinder 1 C-27
    P1327 Knock Control Maximum Spark Limit Cylinder 2 C-27
    P1328 Knock Control Maximum Spark Limit Cylinder 3 C-27
    P1329 Knock Control Maximum Spark Limit Cylinder 4 C-27
    P1372 Crankshaft Sensor Segment Error C-06
    P1372 Crankshaft Sensor Adaption Error C-06
    P1481 Fan Relay 1 Circuit High C-34
    P1481 Fan Relay 1 Signal Low / Open Circuit C-34
    P1482 Fan Relay 2 Circuit High C-34
    P1482 Fan Relay 2 Signal Low / Open Circuit C-34
    P1500 Electronic Throttle Control Motor Failure C-09
    P1500 Electronic Throttle Control Motor Failure C-09
    P1520 Powerstage Currentless C-02
    P1525 Limp Home Position Error C-09
    P1526 Throttle Position Adaption Error C-09
    P1526 Throttle Position no Adaption C-09
    P1526 Limp Home Adaption Error C-09
    P1526 Lower Limit Adaption Error C-09
    P1530 A/C Relay Voltage High Air Conditioning System B-10
    P1530 A/C Relay Circuit Open Air Conditioning System B-10
    P1540 Air Conditioning Pressure Invalid Signal Air Conditioning System B-10
    P1540 Air Conditioning Pressure Signal High Input Air Conditioning System B-05
    P1540 Air Conditioning Pressure Signal Low Input Air Conditioning System B-10
    P1540 Air Conditioning Pressure Open Circuit Air Conditioning System B-05
    P1540 Air Conditioning Pressure Invalid Signal Air Conditioning System B-10
    P1550 Electronic Throttle Control Reduced Power C-09
    P1550 Electronic Throttle Control Forced Idle C-09
    P1550 Electronic Throttle Control Power Management C-09
    P1550 Electronic Throttle Control Engine Stop C-09
    P1551 Engine Torque Always Higher Than Expected C-02
    P1555 Throttle Position Sensor (TPS) Load Signal not Plausible with Engine Load C-09
    P1600 Reprogram or Replace Electronic Control Unit (ECU) C-02
    P1606 Replace Electronic Control Unit (ECU) C-02
    P1606 Replace Electronic Control Unit (ECU) C-02
    P1606 Replace Electronic Control Unit (ECU) C-02
    P1610 Security Code Not Programmed Immobiliser B-07
    P1611 Wrong Security Code Entered Immobiliser C-02
    P1612 Immobiliser No Or Wrong Signal Immobiliser C-05
    P1613 Immobiliser No Or Wrong Signal Immobiliser C-05
    P1614 Wrong Security Code received Immobiliser C-06
    P1614 Wrong Security Code received Immobiliser C-06
    P1615 Wrong Vehicle ID from Body Control Module C-40
    P1616 Wrong Vehicle ID from Instrument Control Module C-40
    P1650 Service Vehicle Soon Light Voltage High C-37
    P1650 Service Vehicle Soon Light Voltage Low C-37
    P1700 SVS request via CAN B-06
    U2100 CAN-BUS Malfunction C-05
    U2101 CAN-BUS Maximum Configuration List not Programmed C-05
    U2104 CAN-BUS reset counter overrun C-05
    U2106 CAN-BUS no Communication with TCM B-05
    U2108 CAN-BUS no Communication
    with ABS/TC B-08

  2. Remove Advertisements
    MigWeb.co.uk
    Advertisements
     

  3. #2
    MIGWeb Moderator Paul's Avatar
    Join Date
    Nov 2001
    Location
    Midlands
    Posts
    28,581
    Drives
    Most days

    Re: Pedal Test - Fault Code Reading Instructions

    Good info, been posted a few time but someone always asks

  4. #3
    MIGWeb Moderator Pitstoppete's Avatar
    Join Date
    Oct 2003
    Location
    SO52
    Posts
    2,590
    Drives

    Re: Pedal Test - Fault Code Reading Instructions

    for what vehicles?

  5. #4
    MSG
    MSG is offline
    MIGWeb User
    Join Date
    Apr 2005
    Location
    Isle of Dogs
    Posts
    16,813
    Drives
    Calibra Eco 16V 2L

    Re: Pedal Test - Fault Code Reading Instructions

    Very usefull indeed, Good find Dave.
    Who said the universe came from no where! flippin heck, its been around for 13.76389271 billions of years around!

  6. #5
    MIGWeb User
    Join Date
    Jan 2012
    Location
    london
    Posts
    27
    Drives
    vectra c 2.2 elite

    Re: Pedal Test - Fault Code Reading Instructions

    Does this work on vectra c

  7. #6
    Administrator. GTE 16v's Avatar
    Join Date
    Jul 2004
    Posts
    11,148
    Drives
    3 x Astras.
    Thread Starter

    Re: Pedal Test - Fault Code Reading Instructions

    Yes

  8. #7
    MIGWeb User
    Join Date
    Jan 2012
    Location
    london
    Posts
    27
    Drives
    vectra c 2.2 elite

    Re: Pedal Test - Fault Code Reading Instructions

    well it dont work on mine

  9. #8
    MIGWeb Moderator Paul's Avatar
    Join Date
    Nov 2001
    Location
    Midlands
    Posts
    28,581
    Drives
    Most days

    Re: Pedal Test - Fault Code Reading Instructions

    Pass then.

  10. #9
    MIGWeb User
    Join Date
    Apr 2006
    Location
    Atherstone
    Posts
    894
    Drives
    transit, bora 4motion

    Re: Pedal Test - Fault Code Reading Instructions

    poo a brick i never knew that!!!
    has scrapped the sig with all the cars to do list!!!!! 3 novas i own says it all really

  11. #10
    MIGWeb User
    Join Date
    Oct 2011
    Location
    Berlin
    Posts
    36
    Drives
    Astra MK3 GSI

    Re: Pedal Test - Fault Code Reading Instructions

    for wich cars does it work?
    Ich bin ein Berliner !

  12. #11
    MIGWeb Moderator Paul's Avatar
    Join Date
    Nov 2001
    Location
    Midlands
    Posts
    28,581
    Drives
    Most days

    Re: Pedal Test - Fault Code Reading Instructions

    Won't work on your Mk3.

  13. #12
    MIGWeb User
    Join Date
    Dec 2002
    Location
    Essex
    Posts
    15,839
    Drives
    Lada Riva

    Re: Pedal Test - Fault Code Reading Instructions

    Zafira B 120 spanner light is constantly on . Can anyone help with that please ?

    Zafira 120 , maybe for you newer car folk on here .
    I canny invest in ya and for that reason , I'm oot .

  14. #13
    MIGWeb User
    Join Date
    Oct 2011
    Location
    Berlin
    Posts
    36
    Drives
    Astra MK3 GSI

    Re: Pedal Test - Fault Code Reading Instructions

    damn it XD
    Ich bin ein Berliner !

  15. #14
    MIGClub Member
    Join Date
    Sep 2009
    Location
    Isle of lewis
    Posts
    5,515
    Drives
    Cavalier turbo, Corsas,

    Re: Pedal Test - Fault Code Reading Instructions

    Astra G. will this work?

  16. #15
    MIGWeb User
    Join Date
    Mar 2008
    Location
    Hertfordshire
    Posts
    908
    Drives
    Vectra B GSI, Zafira GSI

    Re: Pedal Test - Fault Code Reading Instructions

    How about a Zafira A GSI as it doesnt have a spanner light it has an engine one?

  17. #16
    Moderator / Memberships Astra Dan's Avatar
    Join Date
    Feb 2002
    Location
    Fareham, Hants.
    Posts
    18,350
    Drives
    13S C20XE X20XEV

    Re: Pedal Test - Fault Code Reading Instructions

    The only way to know is to try it.
    They're there, in their room.

  18. #17
    MIGWeb Moderator Paul's Avatar
    Join Date
    Nov 2001
    Location
    Midlands
    Posts
    28,581
    Drives
    Most days

    Re: Pedal Test - Fault Code Reading Instructions

    And let us know.

  19. #18
    Moderator / Memberships Astra Dan's Avatar
    Join Date
    Feb 2002
    Location
    Fareham, Hants.
    Posts
    18,350
    Drives
    13S C20XE X20XEV

    Re: Pedal Test - Fault Code Reading Instructions

    Think you can only do it on cars with the light.
    They're there, in their room.

  20. #19
    MIGWeb User
    Join Date
    Jun 2003
    Location
    now in a evo
    Posts
    7,286
    Drives
    1.4bar = 356bhp :-)

    Re: Pedal Test - Fault Code Reading Instructions

    i have the spanner and ecu light the pedal method doesnt work for me. 2005 astra van 1.7cdti

  21. #20
    MIGWeb User
    Join Date
    Mar 2008
    Location
    Hertfordshire
    Posts
    908
    Drives
    Vectra B GSI, Zafira GSI

    Re: Pedal Test - Fault Code Reading Instructions

    It did work and come up with P0170 Rich Exhaust C-30/P0170 Lean Exhaust C-30

    Ive been meaning to move a spring clip that is stopping the actuator opening fully for a few months now,could that be the cause?

  22. #21
    MIGWeb User
    Join Date
    Oct 2004
    Location
    Deganwy, North Wales
    Posts
    279
    Drives
    Astra SRI, Transit Connec
    Hi guys i got

    10
    1
    3

    Can someone disipher that for me?

    130?
    Fiesta XR Turbo Technics Phat Boy gone......
    Astra SRI Low boy here....

  23. #22
    MIGWeb User
    Join Date
    Mar 2013
    Posts
    1
    Drives

    Re: Pedal Test - Fault Code Reading Instructions

    THANKS Alan did pedal test and got 0500 witch is speed sensor malfunction!
    Any more advice you can give me on that problem?

  24. #23
    MIGWeb User
    Join Date
    Jan 2005
    Location
    M1 J29A
    Posts
    971
    Drives
    Veccy GSI

    Re: Pedal Test - Fault Code Reading Instructions

    Just an addition to this....

    I pedal tested a Zaf 04 plate diesel the other month, standard pedal test didn't work. However, ignition to 2 (dash lights up) then pressing the pedals worked. However, it wasn't a flash code, the numbers were displayed on the odometer.
    If my post contains the line 'Last edited by Nemesis;' Then don't trust anything above, as I didn't write it.

  25. #24
    MIGWeb User
    Join Date
    May 2013
    Posts
    16
    Drives

    Re: Pedal Test - Fault Code Reading Instructions

    Can some one help me work this out did a video to help

    Astra turbo code - YouTube

  26. #25
    MIGWeb User
    Join Date
    May 2013
    Posts
    9
    Drives

    Re: Pedal Test - Fault Code Reading Instructions

    P0300 missfire unidentified cylinder b-21 detected what do I do from this point ?

+ Reply to Thread
Page 1 of 2 1 2 LastLast

LinkBacks (?)

  1. 04-03-2014, 13:14
  2. 07-02-2014, 11:44
  3. 30-01-2014, 18:59
  4. 28-01-2014, 14:23
  5. 14-01-2014, 09:19
  6. 03-12-2013, 06:36
  7. 06-11-2013, 19:37
  8. 13-10-2013, 08:15
  9. 04-09-2013, 07:30
  10. 23-07-2013, 21:34
  11. 21-07-2013, 08:01
  12. 24-06-2013, 20:26
  13. 14-06-2013, 14:05
  14. 26-05-2013, 14:28
  15. 22-05-2013, 15:47
  16. 22-04-2013, 16:01
  17. 30-03-2013, 21:53
  18. 07-01-2013, 15:34
  19. 27-11-2012, 00:41
  20. 08-10-2012, 22:04
  21. 08-09-2012, 16:34
  22. 03-07-2012, 08:38
  23. 30-05-2012, 11:52
  24. 02-01-2012, 16:21

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts